Papers about voiding
by Dr. Ning-Cheng Lee , Dr. Benlih Huang, William Manning, Dr. Yan Liu
Voiding is attributed to the flux outgassing within the solder joints when the solder is at molten state. The effect of reflow profile on voiding at microvia for lead-free soldering is strongly dependent on the flux chemistry. In general, wetting is more important than
melting outgasing behavior, and can be enhanced by employing a higher melting energy, including both higher peak temperature and longer dwell time. Use of a high soaking energy can help drying out volatiles hence reduce the melting outgasing and result in low
voiding, but may also increase oxidation for pastes with poor oxidation resistance and cause a high voiding. Testing oxidation resistance of solder paste beforehand will promise a more accurate selection of soaking energy.
pb-free, soldering, BGA, CSP, void, voiding, SMT, solder, lead-free, microvia, profile, reflow
[Permanent Link to this Paper ]
Posted on 2 Mar 2010
by Dr. Arnab Dasgupta, Dr. Benlih Huang, Dr. Ning-Cheng Lee
For SnAgCu solder, the voiding rate at microvia was studied with the use of simulated microvia, and was the lowest with 95.5Sn3.8Ag0.7Cu and 95.5Sn3.5Ag1Cu, and increased with further decrease in Ag content. Results indicated that voiding at microvia was governed by via filling and exclusion of fluxes. The voiding rate decreased with decreasing surface tension and increasing wetting force which in turn was dictated by the solder wetting or spreading. Both low surface tension and high solder wetting prevented the flux from being entrapped within microvia. A fast wetting speed might also facilitate reducing voiding. However, this factor was considered not as important as the final solder coverage area.
pb-free, reflow, surface mount, microvia, voiding, void, lead-free, soldering, solder
[Permanent Link to this Paper ]
Posted on 4 Mar 2010
by Dr. Ning-Cheng Lee , HongWen Zhang
Although lead-free soldering has been the main stream of industry since 2006, with the replacement of eutectic SnPb system by SnAgCu system, the development of drop-in lead-free alternatives for high melting high lead solder alloys is still far from mature. BiAg alloy exhibits acceptable bulk strength but very poor ductility and wetting, therefore it is not acceptable as an option. In current work, a mixed powder BiAgX solder paste system has been developed as a viable alternative, high temperature lead free solder. The metal powder in the paste is composed of a high melting first alloy powder as majority and the additive powder as minority. The additive contains a reactive element to react with various metallization surface finishes. The additive will melt and react on the parts before or together with the melting of the majority solder. The reactive element in the additive is designed to be converted completely into IMCs during the reflow process, hence resulting in a high melting solder joint. In the mixed powder paste system, a melting temperature above 260°C was verified by both DSC and TMA data. The mixed powder solders show a significantly improved wetting comparing to Bi11Ag. The voiding and TCT performance are comparable with high lead solders. The IMC layer thickness of the mixed powder system is insensitive toward thermal aging at 175°C, while the high lead ones do show a considerable increase.
BiAg, voiding, wetting, mixed alloy, solder joint, solder paste, solder, lead-free, high temperature
[Permanent Link to this Paper ]
Posted on 20 Oct 2011
by Harish Gadepalli, Rangaraj Dhanasekaran, Dr. S. Manian Ramkumar, Timothy Jensen , Ed Briggs
Quad Flatpack No lead (QFN) packages have become a popular choice in electronics packaging due to its small form factor. They are also gaining rapid industry acceptance because of its excellent thermal and electrical performance. The bottom side of the QFN package has a large thermal pad. This exposed die attach pad effectively conducts heat to the PCB and also provides a stable ground connection. Effective soldering of this surface to the pad on the PCB is required for good thermal dissipation and component functionality. The exposed thermal pad presents various challenges during the surface mount assembly process. One major challenge is solder void formation. Voids are primarily formed due to the entrapment of volatiles in flux outgassing during the reflow process.
The primary objective of this study is to determine optimal parameters to minimize void formation in QFN packages (QFN16 and QFN20), specifically the reflow profile, leadfree solder paste and stencil aperture opening for the thermal pad. A systematic DOE based approach was used to arrive at conclusions, using the ratio of void volume on the thermal pad to the actual volume of solder paste printed as the response variable. Various graphs are presented to understand the impact of different parameters. Interaction graphs were used to determine optimal settings for each parameter.
reflow profile, lead-free, voiding, solder paste
[Permanent Link to this Paper ]
Posted on 21 Jan 2011
by Dr. Ning-Cheng Lee
Reflow soldering of solder paste is the primary interconnection method used in SMT assembly process. The major issues which plague the reflow soldering performance include, but not limited to, bottom-side-component-holding, bridging, dewetting, low-residue, opening, solder balling, solder beading, solder-fillet-lifting, tombstoning, defective balling for BGA, and voiding. The mechanisms, causes, and cures for each issue are briefly discussed in this article.
lead-free, soldering, solder paste, SMT, bridging, dewetting, opening, solder balling, solder beading, solder-fillet-lifting, tombstoning, balling for BGA, voiding, pb-free, reflow
[Permanent Link to this Paper ]
Posted on 1 Jan 2009
by Dr. Ning-Cheng Lee , Dr. Arnab Dasgupta, Dr. Runsheng Mao, Dr. Yan Liu
Electronic industry has been driven toward lead-free by RoHS (Restriction of Hazardous Substances Directive) which is in force since 2006. Recently REACH (Registration, Evaluation and Authorization of Chemicals) further drives the industry toward halogen-free. As a result, solder pastes for PCB assembly are required or desired to be both lead-free and halogen-free. Lead-free solder alloys in general wet poorer than tin-lead due to the higher surface tension of the former alloys. In the mean time, halogen-free fluxes typically also wet poorer than the more powerful halogen-containing fluxes. Consequently, the lead-free and halogen-free solder paste products that emerged inevitably suffer from a considerably inferior soldering performance than that of conventional halogen-containing tin-lead solder pastes. The deficiencies include poor wetting, solder balling, voiding, graping, head-in-pillow, etc. This gap is particularly significant for fine-pitch applications where the impact of oxidation is more profound. Furthermore, the higher soldering temperature of the higher melting lead-free alloys also aggravates the challenge of in-circuit test for no- clean processes, mainly due to the difficulty for probe to penetrate through the toughened flux residue. Although use of inert reflow atmosphere may alleviate some of the problems, the higher cost of it is prohibitive for most of the manufacturing firms. In this work, a halogen-free lead-free no-clean solder paste system, Indium8.9HF series, has been developed. It exhibits superior oxidation tolerance, thus assures superior resistance against graping, head-in-pillow, solder balling, voiding, and poor wetting for miniaturized electronic applications. In spite of the immense challenge in material science, this system also shows outstanding probe testability, in addition to its very good printability, non- slump, SIR, and ECM performance. The superior performance of this Indium8.9HF system effectively sealed the gap caused by lead-free and halogen-free requirements.
lead-free, halogen-free, no-clean, solder, solder paste, miniaturization, graping, head-in-pillow, voiding, solder balling, probe testability, ICT, oxidation
[Permanent Link to this Paper ]
Posted on 1 Jan 2009
by Derrick Herron, Dr. Yan Liu, Dr. Ning-Cheng Lee
Quad-flat no-leads (QFN) package designs are receiving more and more attention in the electronics industry. This package offers a number of benefits including (1) small size, such as a near die size footprint, thin profile, and light weight; (2) easy PCB trace routing due to the use of perimeter I/O pads; (3) reduced lead inductance; and (4) good thermal and electrical performance due to the adoption of exposed copper die-pad technology. These features make the QFN an ideal choice for many new applications where size, weight, electrical, and thermal properties are important. However, the adoption of QFN often runs into voiding issue at SMT assembly. Upon reflow, outgassing of solder paste flux at the large thermal pad has difficulty escaping and inevitably results in voiding. It is well known that the presence of voids will affect the mechanical properties of joints and deteriorate the strength, ductility, creep, and fatigue life. In addition, voids could also produce spot overheating, lessening the reliability of the joints. This is particularly a concern for QFN where the primary function of thermal pads is for heat dissipation. Thermal pad voiding control at QFN assembly is a major challenge due to the large coverage area, large number of thermal via, and low standoff. Both design and process were studied for minimizing and controlling the voiding. Eliminating the thermal via by plugging is most effective in reducing the voiding. For unplugged via situations, a full thermal pad is desired for a low number of via. For a large number of via, a divided thermal pad is preferred due to better venting capability. Placement of a thermal via at the perimeter prevents voiding caused by the via. A wider venting channel has a negligible effect on voiding and reduces joint continuity. For a divided thermal pad, the SMD system is more favorable than the NSMD system, with the latter suffering more voiding due to a thinner solder joint and possibly board outgassing. Performance of a divided thermal pad is dictated by venting accessibility, not by the shape. Voiding reduction increases with increasing venting accessibility, although the introduction of a channel area compromises the continuity of the solder joint. Reduced solder paste volume causes more voiding. Short profiles and long hot profiles are most promising in reducing the voiding. Voiding behavior of a QFN is similar to typical SMT voiding and increases with pad oxidation and further reflow.
voiding, thermal pad, solder, solder paste, SMT, flux, Apex 2011, QFN assembly
[Permanent Link to this Paper ]
Posted on 11 Apr 2011
by Wanda B. Hance, Dr. Ning-Cheng Lee
The mechanisms for void formation are investigated for applications involving solder paste in SMT. Generally the voids are caused by the outgassing of entrapped flux in the sandwiched solder during reflow. The voiding is mainly dictated by the solderability of metallization, and increases with decreasing solderability of metallization, decreasing flux activity, increasing metal load of powder, and increasing coverage area under the lead of the joint. Decrease in the solder powder particle size shows only a slightly negative effect toward voiding. The data indicate that voiding is also a function of the timing between the coalescing of solder powder and the elimination of immobile metallization oxide. The sooner the paste coalescing occurs, the worse the voiding will be. Increase in voiding usually is accompanied by an increasing fraction of large voids, suggesting factors causing voiding will have an even greater impact on the joint reliability than what shown by the total-void-volume analysis results. Preliminary data show that certain predry treatment and flux solvent with higher boiling point appear to cause increased voiding.
lead-free, pb-free, solderability, reflow, solder joint, SMT, voiding, void, flux, solder paste, soldering, solder
[Permanent Link to this Paper ]
Posted on 1 Jan 2009
