블로그

여러분, 최근 포스팅에서 무연 솔더의 용융 온도가 높을수록 리플로 납땜 온도가 더 높아야 하므로 무연에 더 많은 전기가 사용된다고 설명했습니다.

If you are left with an indium sulfamate plating bath or solution that you no longer use or need, you may have wondered what to do with it. It may be surprising to know that the indium plating bath

One of the first activities any child enjoys, once they can manipulate things, is usingpaints and crayons to color pictures.Stay with me: there's a reason for this introduction. In the lastsix

Last week I spent some time in the Advanced Materials and Process Development Lab with Eric Bastow, verifying the printing characteristics of our newest low temp metallization paste LT-918.Due to its

TypicalTabbing Ribbon Solders Only a few solder alloys have become common, industry-wide, among solarmodule assemblers, and those can be pared down into three categories: BiSn alloys (58Bi42Sn,

Included in a solder paste‘s Product Data Sheet, among other things, are general guidelines which aid the customer in designing an SMT reflow profile. The data sheet gives general

최근 테스트 결과에 따르면 솔더 플럭스는 높은 리플로우 온도(>450°C)를 처리하여 예상보다 우수한 시각적 플럭스 잔류물 결과를 제공합니다! 솔더 플럭스는 전통적으로

Solder starvation is a serious electronics assembly issue – with a very simple solution. Solder starvation occurs when adequate volumes of solder are not available to effect a perfectly-shaped

Unbeknowst to me, the refrigerator where I store my solder paste and fluxes that I use for SIR (Surface Insulation Resistance) testing was being moved. One of my colleagues showed up at my desk with

Based on a recent post I published regarding the use of bismuth (Bi)in solder alloys, John writes: "If Bismuth comes from the production of Pb, and if the use of Pb is being reduced, won’t

Folks, A few people asked some questions after my last post on bismuth solders.Here they are: 1. The low melting point of these solders is encouraging.What are realistic field use conditions? Bismuth

Folks, When the industry was preparing to transition to lead-free solders almost ten years ago (can it have been that long), tin-bismuth solders were serious candidates.Their low melting point, of

Nitinol (a nickel titanium alloy) has become a very important material, especially in the medical world. It is often necessary to "attach" Nitinol to another piece of Nitinol or some other

Folks, In a recent post, I shared my perspective on the pluses, minuses and neutral aspects of lead-free solder assembly.In the minus category, I listed tin whiskers.A few people commented that tin

ITO is one of the materials that makes the magic of flat panel displays (monitors, TVs, etc.) possible. When sputtered on in a thin layer, it acts as a transparent conductive film. However, the

I was asked this week to contribute to the upcoming IPC handbook (IPC-CH-65 HDBK) on the section on contamination and its effects on printed wiring assemblies (PWA’s). There is a clear crossover of

Conformal coating compatibility with no-clean flux residues has been a major topic for years – becoming even more popular recently with companies looking to cut manufacturing costs and

This week a customer in Asia asked why one of our new epoxy fluxes was not allowing the package-on-package (PoP) device to be picked up from the dipping tray. Obviously, the vacuum nozzle must have

Folks, Patty had been working with engineering on a new product that needed a very precise and controlled volume of the stencil printed “brick” of solder paste on the PWB pads. The product had

Folks, Let’s assume you are trying to improve the productivity of your SMT assembly lines. You work at a facility that manufactures high volume products with a high mix. The first aspect of your

Folks, The conclusion of the Bob and Fred break saga…… Phil stared, “The uptime on AXI’s four SMT production lines is…….” Fred and Bob were waiting for the good news of