블로그

Folks, Let’s see how Patty is recovering from her conflict with Hal Lindsay……. Patty saw a link on one of the daily SMT Tech newsletters that piqued her interest. It was titled, “A New Alloy

모든 금속이 서로 잘 어울리는 것은 아닙니다. 이는 전자제품과 그 안에 사용되는 재료의 세계에도 적용됩니다. 비교적 새롭고 관련성이 높은 사례는 RoHS의 출현과 함께 등장한

Folks, It's been awhile, let's see what Patty is up to… Patty was in her office, finishing lunch and reading Golf Digest. She was happy to see Tiger Woods doing better, but a little

Here’s an interesting technology fact I just learned: Indium Sulfide was the very first indium compound to be discovered. I bet Reich and Richter (the discovers of indium) never imagined that

Folks, Let’s see how Patty is doing with her latest challenge….. Patty had decided to call The Professor and see what advice he had to offer in preparation for her visit to the facility

여러분, 패티에게 무슨 일이 있었는지 봅시다........ 패티는 조금 피곤한 듯 컴퓨터 앞에 앉아있었습니다. 그녀는 콜로니얼 윌리엄스버그에서 일주일간의 휴가를 마치고 막 돌아온 뒤였습니다.

웨이퍼 범핑 공정은 지난 10년 동안 발전해 왔습니다. 반도체 조립 산업은 솔더 페이스트 프린팅을 사용하는 범핑 공정에서 보이드에 대한 모든 우려를 안고 있습니다,

It is no secret that automotive semiconductor customers are becoming increasingly demanding. The “under the hood / bonnet” electronics environment is arguably one of the most thermally

NanoFoil®requires a threshold of energy to activate. What happens if that energy value is not met?: Interdiffusion and inhibition of the NanoBond® reaction. This can happen if NanoFoil®

Many surface finishes are solderable with the right flux. Many of our electronic devices use solder to bond copper, silver, gold, and other metals, but did you know that you can solder wooden

Being the Indium Corporation, we know what indium is, where it comes from, and how to use it. But sometimes we forget that not everyone is as immersed in indium as we are. So what is indium? Of

Folks, In the category of interesting requests, Ron, a gold worker, from Guyana, sent me the following note: Dr. Ron, My colleagues use a “wet” gold technique to measure gold alloy

There are many sputtering target materials that are tricky to solder to. For those alloys we ‘bring out the big guns’ – in this case, our ultrasonic soldering

In order to NanoBond® parts that are made out of copper, nickel, or platinum, we must first apply solder to the bonding surface. This is most commonly done by melting solder directly onto the

여러분, 와이불 분석에 대한 이야기를 계속해 보겠습니다…… 여러분이 열심히 작업하여 열 사이클 시험을 위해 무연 SMT PCB를 조립했다고 가정해 봅시다. 최고의 무연 솔더 페이스트를 사용했고,

Sometimes one piece of NanoFoil® just isn’t enough… We often NanoBond® sputtering targets which are large enough to require multiple sheets of NanoFoil® to cover the width or

Hand cutting is only one option for shaping NanoFoil®, however it is quick, easy, and inexpensive. All you need to cut NanoFoil® with this method is a good cutting surface, metal straight

Folks, In continuing our discussion on Weibull Analysis, let’s assume we assembled some SMT and through-hole PCBs with lead-free solder paste. On this board are also some bottom-side terminated

A few years back, Indium Corporation's own Eric Bastow set up a prototype NanoFoil® plating process to demonstrate the material and cost savings of setting up a small plating bath. One of the

One question that I often hear from customers is; “Once out of the refrigerator, how long do I have to wait to allow my solder paste and/or flux to reach room temperature in order to use

솔더 페이스트 '그레이프' 결함에 대해 들어본 적이 있지만, 작은 부품을 부착하는 데 사용되는 솔더 와셔 프리폼과 같은 다른 솔더 형태에서도 동일한 산화 문제가 발생합니다.